Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
We've encountered this post relating to How to Install a Bathtub down the page on the internet and reckoned it made good sense to share it with you here.
Installing a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging task. If the old bathtub is readily accessible, the task can relocate speedily; if you need to open up a wall surface to remove the old bathtub and also place the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will need a helper to move out the old bathtub and embeded in the brand-new one. See to it you have certified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This article will help you set up a new bath tub in your shower room if you have already bought a brand-new tub and also do not need to transform the setup of your previous supply of water pipelines.
Your devices and also product checklist should comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite problematic because of the limited access that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth ready for the remaining water that will originate from the pipes. Once the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new taps, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Secure the tap in position with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind should be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Utilizing both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub till the level reads degree.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water supply and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the tub and also examine the overflow outlet and the regular outlet for leakages.
Ultimately, deal with the bath paneling as explained in the supplier's user's manual. Tiling and also securing around the bathtub ought to wait up until the tub has been utilized a minimum of when as this will resolve it right into its last setting.
Preparing for the Installation
First of all, the supporting frame provided with the bath should be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, creating the water to pass through the wall between the bath as well as the tiling, leading to problems with moisture and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealer can split relatively early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that report about A Step-by-Step Guide to Installing a Bathtub from a good friend on our other web page. Those who enjoyed reading our article please be sure to share it. Thanks a lot for your time. Visit us again soon.
Professional service available. Report this page